Product FAQ

All Deep Silence cases include on the front panel that controls up to 6 or 8 fans. All fan controllers require power and must be connected to a power supply to function.

The fan controller built-in all Deep Silence cases connects to the power supply using Molex cables and uses only 2 of the 4 pins.

Unfortunately, they are not. But we do include dust filters that are easily removable, washable and replaceable. Some of our fans are available in an easy to clean, removable brackets and filters.

Fan wires:
Red: +12V
Yellow: Control
Black: Ground

Molex wires:
Yellow: +12V
Red: +5V
Black: Ground

Splicing instructions:
1. Take the Yellow wire from Molex and connect it to Red wire from fan.
2. Take the Black wire from Molex and connect it to Black wire from fan.
3. This will cause the fan to run at full speed continuously (no fan speed control).You can use a crimping tool if you have one if not squeezing them tightly with a pair of pliers should do the job.Happy modding!

Many liquid coolers include fans for only one side (push or pull) of the radiator.You may be tempted to use the stock case fan to createa push-pullsetup.While you can definitely use the stock fans in a push-pull radiator, the Deep Silence fans were designed to match the case's fan controller. This means the stock case fans may not rotate in sync with the fans from other brands, leading to additional air turbulence (airborne noises).

Absolutely! 4-pin fans are designed with Pulse Width Modulation (PWM) used by motherboards.The Nanoxia Deep Silence cases come with fan controllers with 3-pin power connectors anddonot need PWM.Simply plug 4-pin fan to the 3-pin power connector with the PWM-pin unfilled. There is no adapter needed.

To ensure maximum fan speed of 12V, make sure:
1. Do not use the included 7V cable (included in select fan models).
2. Slide the fan controller switch all the way to max.

You may splice the cables and use just 2 wires (red and black).The third wire (yellow) is used for speed control / RPM by the motherboard.

The Nanoxia Deep Silence fans use Rifle bearings. This is similar to sleeve bearings, but are quieter and have almost as much lifespan as ball bearings. These bearings have a spiral groove in it that circulates lubricants from a reservoir. The use of rifle bearings allows our fans to be near-silent and last a very long time.Can I fit a wide GPU inside the Project S case?

The fans included in our cases are not LED. They do not light up.Can I fit a wide GPU inside the Project S case?

All Deep Silence cases come with filter screens on the front intake fans. If your top fans are exhausting hot air, you don't need filters.

The Deep Silence fans are 25 mm in thickness and are not slim profile fans.

Most power supplies come with their own, proprietary modular cables. The Nanoxia 24 pin ATX extension is designed to fit power supply cables and does not fit directly to the power supply itself.

The CoolForce aluminum cable combs are machined with a . They are ideally suited for Nanoxia cables, but you may use these clips with any sleeved cable up to 3mm in thickness.

This depends on the size of the case, the location of the liquid cooler and other PC components you have installed inside the case.

Using Deep Silence 1 as an example, this case measures 517 x 220 x 532 mm (height x width x depth). The longest distance between the front bottom corner, to the top rear corner of the case, is about 741 mm. We highly recommend that you go with greater than 400mm tube length whenever possible.

This would give you more "slack" in case you need to route the tube to other PC components.

Our CoolForce Collant, which contains Ethylene Glycol, is safe to use with PETG tubes. Ethylene Glycol is one of the components used in making PETG products.

The recommended place to install large radiators like the Corsair H100GT is under the top panel. Please refer to the for mounting screw holes available in Deep Silence 5 top panel.

Aqua-Pure Water is double distilled water and contains absolutely no additives of any kind, such as dyes, anti-freeze or biological growth inhibitors. Aqua-Pure Water is safe to add to any liquid cooling system.

Pure & Power is one of the various choices from our Cooling Fluids Pro series of coolant, which contains a special mixture of additives for corrosion protection for copper, nickel, aluminum, and brass. Pure & Power is not UV reactive.

We also offer UV reactive coolant in a variety of colors: Acid Green, Clear, Blue, Green, Blood Red.

The CoolForce LED fittings are designed for PETG hard tubes, such as CF-PETG450 or CF-PETG550. These LED fittings are not recommended for use with PVC flexible tubes.

All CoolForce coolant (such as CF1 Acid Green) already includes biocide and corrosion inhibitors, so you don't really need a silver coil. While silver coils inhibit bio growth, they do not provide corrosion protection. If you introduce another type of liquid such as distilled water, you should consider adding biocide and corrosion inhibitors, such as CF1 Base.

The CF No. 1 coolants contain less than 0.0005% ethylene glycol andaresuitable for all water cooling systems.

We do not recommend connecting to a slightly smaller 12 mm inner diameter tubes as this prevents proper sealing of the circuit. The Nanoxia CoolForce LED fittings are ideally suited to connect our CoolForce 16/13 PETG tubes (or any other acrylic tubes with identical dimension) and components with a G 1/4 inner threads.

Our UV bars are on the blue spectrum of UV and gives off a very soft hint of purple not noticeable in daylight.

While our UV bars may look blue-ish in color, most of the light it emits is in the ultraviolet (UV) range of the spectrum, which is invisible to the human eye.

Our LED bars are quite powerful andrequiremore power than most motherboards can provide. A single 20 cm bar consumes 4.4 Watts, while a 30 cm bar requires 6.4 Watts! Since most motherboard fan headers are not capable of delivering such power, as aresult, the LED bars will flicker (or simply not work at all). To achieve maximum brightness, please connect the LED bars directly to a power supply using the included 3-pinMolexconnector.

To request for spare parts, please write to us here.

Make sure you provide a detailed description of the problem and attach a picture of the problem whenever possible.

Our staff will do their best to identify and locate the part you request.

Depending on the spare part you request, there may be fees and/or shipping charges.If there are any fees, our agent will notify you of approval.

At this time, the Deep Silence 6 is the only available case with a window version. We are currently not taking any custom orders for window panels for any of the other models. However, we are looking to have an inventory of these on hand in the coming future. Please check back with us.

The front panel bottom door on the DS1 is secured by 2 pins, one at the top and another at the bottom. In order to remove the front panel door, you need to remove the bottom pin. Please review the picture with the following instructions:

1. Remove 6 rubber pads covering the screws.
2. Once you have unscrewed the front panel door, the bottom pin will become loose.
3. Remove the front panel door.
4. Place the bottom pin back in the front panel door.
5. Tighten the 6 screws and place the rubber pads back on.

All Deep Silence cases are lined with sound dampening materials on the side panels, which complicated cutting using hand tools such as a Dremal. Cutting a window would also significantly reduce its acoustic absorbing properties.

The Deep Silence cases do not include case/motherboard speaker as you probably will barely hear such speaker mounted inside the case due to the sound dampening materials used. Our cases are heavily insulated to provide the best in noise suppression and silent computing, especially if you are in a recording studio.

All Deep Silence cases include on the front panel that controls up to 6 or 8 fans. All fan controllers require power and must be connected to a power supply to function.

The fan controller built-in all Deep Silence cases connects to the power supply using Molex cables and uses only 2 of the 4 pins.

Unfortunately, they are not. But we do include dust filters that are easily removable, washable and replaceable. Some of our fans are available in an easy to clean, removable brackets and filters.

Fan wires:
Red: +12V
Yellow: Control
Black: Ground

Molex wires:
Yellow: +12V
Red: +5V
Black: Ground

Splicing instructions:
1. Take the Yellow wire from Molex and connect it to Red wire from fan.
2. Take the Black wire from Molex and connect it to Black wire from fan.
3. This will cause the fan to run at full speed continuously (no fan speed control).You can use a crimping tool if you have one if not squeezing them tightly with a pair of pliers should do the job.Happy modding!

Many liquid coolers include fans for only one side (push or pull) of the radiator.You may be tempted to use the stock case fan to createa push-pullsetup.While you can definitely use the stock fans in a push-pull radiator, the Deep Silence fans were designed to match the case's fan controller. This means the stock case fans may not rotate in sync with the fans from other brands, leading to additional air turbulence (airborne noises).

Absolutely! 4-pin fans are designed with Pulse Width Modulation (PWM) used by motherboards.The Nanoxia Deep Silence cases come with fan controllers with 3-pin power connectors anddonot need PWM.Simply plug 4-pin fan to the 3-pin power connector with the PWM-pin unfilled. There is no adapter needed.

To ensure maximum fan speed of 12V, make sure:
1. Do not use the included 7V cable (included in select fan models).
2. Slide the fan controller switch all the way to max.

You may splice the cables and use just 2 wires (red and black).The third wire (yellow) is used for speed control / RPM by the motherboard.

The Nanoxia Deep Silence fans use Rifle bearings. This is similar to sleeve bearings, but are quieter and have almost as much lifespan as ball bearings. These bearings have a spiral groove in it that circulates lubricants from a reservoir. The use of rifle bearings allows our fans to be near-silent and last a very long time.Can I fit a wide GPU inside the Project S case?

The fans included in our cases are not LED. They do not light up.Can I fit a wide GPU inside the Project S case?

All Deep Silence cases come with filter screens on the front intake fans. If your top fans are exhausting hot air, you don't need filters.

The Deep Silence fans are 25 mm in thickness and are not slim profile fans.

Most power supplies come with their own, proprietary modular cables. The Nanoxia 24 pin ATX extension is designed to fit power supply cables and does not fit directly to the power supply itself.

The CoolForce aluminum cable combs are machined with a . They are ideally suited for Nanoxia cables, but you may use these clips with any sleeved cable up to 3mm in thickness.

We do not recommend connecting to a slightly smaller 12 mm inner diameter tubes as this prevents proper sealing of the circuit. The Nanoxia CoolForce LED fittings are ideally suited to connect our CoolForce 16/13 PETG tubes (or any other acrylic tubes with identical dimension) and components with a G 1/4 inner threads.

Our UV bars are on the blue spectrum of UV and gives off a very soft hint of purple not noticeable in daylight.

While our UV bars may look blue-ish in color, most of the light it emits is in the ultraviolet (UV) range of the spectrum, which is invisible to the human eye.

Our LED bars are quite powerful andrequiremore power than most motherboards can provide. A single 20 cm bar consumes 4.4 Watts, while a 30 cm bar requires 6.4 Watts! Since most motherboard fan headers are not capable of delivering such power, as aresult, the LED bars will flicker (or simply not work at all). To achieve maximum brightness, please connect the LED bars directly to a power supply using the included 3-pinMolexconnector.